1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
|
// Copyright 2018 The Abseil Authors.
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// https://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
//
// -----------------------------------------------------------------------------
// File: failure_signal_handler.h
// -----------------------------------------------------------------------------
//
// This file configures the Abseil *failure signal handler* to capture and dump
// useful debugging information (such as a stacktrace) upon program failure.
//
// To use the failure signal handler, call `absl::InstallFailureSignalHandler()`
// very early in your program, usually in the first few lines of main():
//
// int main(int argc, char** argv) {
// // Initialize the symbolizer to get a human-readable stack trace
// absl::InitializeSymbolizer(argv[0]);
//
// absl::FailureSignalHandlerOptions options;
// absl::InstallFailureSignalHandler(options);
// DoSomethingInteresting();
// return 0;
// }
//
// Any program that raises a fatal signal (such as `SIGSEGV`, `SIGILL`,
// `SIGFPE`, `SIGABRT`, `SIGTERM`, `SIGBUG`, and `SIGTRAP`) will call the
// installed failure signal handler and provide debugging information to stderr.
//
// Note that you should *not* install the Abseil failure signal handler more
// than once. You may, of course, have another (non-Abseil) failure signal
// handler installed (which would be triggered if Abseil's failure signal
// handler sets `call_previous_handler` to `true`).
#ifndef ABSL_DEBUGGING_FAILURE_SIGNAL_HANDLER_H_
#define ABSL_DEBUGGING_FAILURE_SIGNAL_HANDLER_H_
#include "absl/base/config.h"
namespace absl {
ABSL_NAMESPACE_BEGIN
// FailureSignalHandlerOptions
//
// Struct for holding `absl::InstallFailureSignalHandler()` configuration
// options.
struct FailureSignalHandlerOptions {
// If true, try to symbolize the stacktrace emitted on failure, provided that
// you have initialized a symbolizer for that purpose. (See symbolize.h for
// more information.)
bool symbolize_stacktrace = true;
// If true, try to run signal handlers on an alternate stack (if supported on
// the given platform). An alternate stack is useful for program crashes due
// to a stack overflow; by running on a alternate stack, the signal handler
// may run even when normal stack space has been exausted. The downside of
// using an alternate stack is that extra memory for the alternate stack needs
// to be pre-allocated.
bool use_alternate_stack = true;
// If positive, indicates the number of seconds after which the failure signal
// handler is invoked to abort the program. Setting such an alarm is useful in
// cases where the failure signal handler itself may become hung or
// deadlocked.
int alarm_on_failure_secs = 3;
// If true, call the previously registered signal handler for the signal that
// was received (if one was registered) after the existing signal handler
// runs. This mechanism can be used to chain signal handlers together.
//
// If false, the signal is raised to the default handler for that signal
// (which normally terminates the program).
//
// IMPORTANT: If true, the chained fatal signal handlers must not try to
// recover from the fatal signal. Instead, they should terminate the program
// via some mechanism, like raising the default handler for the signal, or by
// calling `_exit()`. Note that the failure signal handler may put parts of
// the Abseil library into a state from which they cannot recover.
bool call_previous_handler = false;
// If non-null, indicates a pointer to a callback function that will be called
// upon failure, with a string argument containing failure data. This function
// may be used as a hook to write failure data to a secondary location, such
// as a log file. This function will also be called with null data, as a hint
// to flush any buffered data before the program may be terminated. Consider
// flushing any buffered data in all calls to this function.
//
// Since this function runs within a signal handler, it should be
// async-signal-safe if possible.
// See http://man7.org/linux/man-pages/man7/signal-safety.7.html
void (*writerfn)(const char*) = nullptr;
};
// InstallFailureSignalHandler()
//
// Installs a signal handler for the common failure signals `SIGSEGV`, `SIGILL`,
// `SIGFPE`, `SIGABRT`, `SIGTERM`, `SIGBUG`, and `SIGTRAP` (provided they exist
// on the given platform). The failure signal handler dumps program failure data
// useful for debugging in an unspecified format to stderr. This data may
// include the program counter, a stacktrace, and register information on some
// systems; do not rely on an exact format for the output, as it is subject to
// change.
void InstallFailureSignalHandler(const FailureSignalHandlerOptions& options);
namespace debugging_internal {
const char* FailureSignalToString(int signo);
} // namespace debugging_internal
ABSL_NAMESPACE_END
} // namespace absl
#endif // ABSL_DEBUGGING_FAILURE_SIGNAL_HANDLER_H_
|
